Keep Every System Running at Peak Performance
Manufacturer-grade maintenance for Trane, Eurapo, SystemAir and Viessmann equipment — delivered by Treimax engineers certified at Trane's Training Centre in France.
Why Maintenance Matters
HVAC systems lose 5–10% of their efficiency every year without proper care. Skipped maintenance shortens equipment life by up to 50%, voids manufacturer warranties, and turns small issues into expensive emergency failures. A maintained chiller, on the other hand, holds its rated efficiency, runs predictably, and delivers full lifecycle value — typically 15–25 years on Trane equipment.
აირჩიეთ ჩვენი ვიზიტების სიხშირე
Semi-Annual Plan
Spring start-up + autumn shutdown
Recommended for residential, light commercial, and seasonal applications. Each visit prepares the system for the upcoming season — cooling-mode commissioning in spring, heating-mode tuning and winter protection in autumn.
Annual Premium Plan
Quarterly with priority service
For mission-critical and 24/7 facilities — hospitals, data centres, hotels, industrial production. Includes everything in the semi-annual plan plus quarterly performance audits and priority emergency response.
What Happens During Each Maintenance Visit
Every visit follows Trane's manufacturer service protocol. Our engineers arrive with calibrated instruments, OEM parts, and a 60-point checklist — and leave you with a written report.
Inspect compressors, condenser fans, and evaporator pumps for wear, vibration, and noise outside spec.
Verify refrigerant charge with electronic gauges; top up or recover refrigerant per F-Gas regulation.
Clean condenser and evaporator coils — measure approach temperatures before and after.
Replace air and water filters; clean strainers and drain pans; clear condensate lines.
Tighten electrical connections; check contactor wear; measure compressor amp draw against nameplate.
Calibrate thermostats, sensors, and BMS/BAS setpoints; download fault logs from the controller.
Test safety circuits — high-pressure cutout, low-pressure switch, freeze-stat, flow switch.
Lubricate motors and bearings where required; inspect belt tension and alignment on AHUs.
Remote Monitoring
Trane Tracer™ controls and BMS integration let our team watch your equipment in real time. Setpoint drift, abnormal compressor cycling, refrigerant pressure anomalies — we see them the moment they happen and dispatch a technician before a fault becomes a failure. Available for any building running a Trane Tracer SC+, Tracer Concierge, or compatible BACnet/Modbus controller.
Factory Oil & Refrigerant Analysis
Annually, we extract a sealed oil sample from each chiller compressor and send it to Trane's accredited analysis lab. The report tells us the exact amount of metallic wear particles, moisture, acidity, and refrigerant breakdown by-products in the oil — a direct read on compressor health months or years before a failure becomes audible. Same goes for refrigerant: gas chromatography detects contamination, mineral oil mixing, or wrong-blend issues that no field gauge will catch.
Your Private Client Portal
Everything about your equipment, in one place
Every Treimax maintenance client gets a dedicated, password-protected web portal for their building. Past and upcoming visits, full PDF service reports, on-site photos from every visit, and live operating data from your equipment — chiller status, which circuit is running, leaving and entering water temperatures, suction and discharge pressures, runtime hours, and active alarms. No phone calls to find out 'how is the system doing' — just open the portal.
Visit History & Reports
Every PDF service report from every visit, archived. Search by date, equipment, or technician.
On-Site Photos
Time-stamped photos from each visit — coil condition, electrical panel, oil sample seal, before/after.
Live Equipment Status
Online / Offline / Fault status for each chiller, AHU and heat pump, refreshed in real time.
Operating Parameters
Active circuit, leaving / entering water temperatures, refrigerant pressures, compressor amps and runtime hours.
Upcoming Schedule
Confirmed dates for your next visits — request a re-schedule or add an extra inspection in two clicks.
Alarm History
Every fault and warning the BMS has raised, with a timestamp, severity, and our follow-up notes.
Let's Build a Maintenance Plan for Your Building
Tell us what equipment you run and how critical your operation is — we'll come on-site, audit the installation, and propose the right plan.